This wiki has been archived and made read-only.
For up-to-date information about TkkrLab and it's projects please visit our main website at tkkrlab.nl.

Difference between revisions of "SpaceState ESP"

From

Jump to: navigation, search
 
Line 1: Line 1:
 
{{Project
 
{{Project
|ProjectName=SpaceState ESP Clock
+
|ProjectName=SpaceState nodeMCU ESP8266 Clock
 
|Owner=zeno4ever
 
|Owner=zeno4ever
|Status=60%
+
|Status=100%
 
|Skillz=Basic Electronics, Arduino Software (C)
 
|Skillz=Basic Electronics, Arduino Software (C)
 
|Summary=Show space open/close state with nodeMCU / ESP-12E / ESP8266
 
|Summary=Show space open/close state with nodeMCU / ESP-12E / ESP8266
Line 26: Line 26:
 
* source code for nodeMCU : https://github.com/zeno4ever/spacestatus_ESP
 
* source code for nodeMCU : https://github.com/zeno4ever/spacestatus_ESP
 
* Library for json processing  https://bblanchon.github.io/ArduinoJson/
 
* Library for json processing  https://bblanchon.github.io/ArduinoJson/
* Arduino IDE for uploading source to nodeMCU
+
* [https://www.arduino.cc/en/Main/Software Arduino IDE] for uploading source to nodeMCU
  
 
=Steps=
 
=Steps=
Line 45: Line 45:
  
 
===LED remarks===
 
===LED remarks===
If you order a LED chip check what type you buy, you have commen anode and commen cathode types. These have to be connected different I uses an common anode. I include setting you can change. I have no tested this part so there may more changes needed to make this work.
+
If you order a LED chip check what type you buy, you have commen anode and commen cathode types. These have to be connected different I used an common anode. I include setting you can change. I have no tested this part so there may more changes needed to make this work.
  
 
I also use one resistor since i only show one color all times. If you want to use more then one color at a time then you should use a resistor per color, so 3 for R,G,B.
 
I also use one resistor since i only show one color all times. If you want to use more then one color at a time then you should use a resistor per color, so 3 for R,G,B.
  
You can cut a part of the LED as long you dont touch the parts where the electroncs are. For me I 'decapped' the LED with a iron saw and sanding it down to have a flat surface.
+
You can cut a part of the LED as long you don't touch the parts where the electronics are. For me I 'decapped' the LED with a iron saw and sanding it down to have a flat surface.

Latest revision as of 18:24, 9 April 2017

Project: SpaceState nodeMCU ESP8266 Clock
SpaceState ESP Picture.jpg
Name SpaceState nodeMCU ESP8266 Clock
Initiator zeno4ever
Status 100%
Skills Basic Electronics, Arduino Software (C)
Summary Show space open/close state with nodeMCU / ESP-12E / ESP8266


I wanted to see if the TkkrLab hackerspace is open on my clock. For this I used an nodeMCU with a RGB led to request the spaceapi every 10 mins and display open (green) or closed (red) status. The nodeMCU is a developer board with an ESP8266 / ESP12-E chip. There are a few different types of nodemcu's, check out this article for more information about these

Resources

Parts List

Software

Steps

Spacestatus schematic.png


I used male breadboard connectors to connect everything to the nodeMCU, you can solder the RGB led directly on the wire (with one resistor on the anode (+))

The clock I have has a 6v that is connected to the Vin and GND of the nodeMCU

  • Check the clock you want to use if there is enough space inside to put nodeMCU inside and where to place the LED.
  • Check if you can use the power of the clock and this is good for Vin. In my case i had 6 V, this in within the range of 4.5V ~ 9V. If you have a other version of nodeMCU check the documentation.
  • Download the source and change the settings for your hackerspace.
  • Upload code to nodeMCU via USB
  • Connect the RGB LED and power in the the nodeMCU


LED remarks

If you order a LED chip check what type you buy, you have commen anode and commen cathode types. These have to be connected different I used an common anode. I include setting you can change. I have no tested this part so there may more changes needed to make this work.

I also use one resistor since i only show one color all times. If you want to use more then one color at a time then you should use a resistor per color, so 3 for R,G,B.

You can cut a part of the LED as long you don't touch the parts where the electronics are. For me I 'decapped' the LED with a iron saw and sanding it down to have a flat surface.